HomeAPA Tuning Guide
Technical GuideAPA Dual-Cam

APA Complete Tuning Process

A step-by-step guide specific to APA dual-cam bows. APA bows tune differently than binary-cam bows — follow this process in order.

01

Maximum Poundage & Initial Specs

Make sure the bow is set to maximum poundage first. If not, tighten limb bolts all the way in and back them out one quarter turn.

Then take a tape measure and measure axle-to-axle and brace height. Axle-to-axle is the most important measurement — it indicates whether draw length is within spec, bow poundage is too high or low, and whether cams are positioned properly. This is especially important on a pre-owned bow. APA bows are true dual-cam and tune differently than binary-cam bows.

Limb Bolts — Tighten all the way in, then back out exactly one quarter turn to reach maximum poundage.
Axle-to-Axle — Measure between axle centres with a tape measure. Most critical spec — confirms draw length, poundage, and cam position.
Brace Height — Measure from the throat of the grip to the string at rest.

Note: APA bows are true dual-cam — not binary. The tuning process is different from most North American bows. Do not apply binary-cam tuning methods here.

02

Cable Position Relative to Cam

Check the position of the cables relative to the cam. The cable should run between the silver reference marks on the cam.

If there are no reference marks, measure from the lobe of the cam to the string — this should be between 5/16" and 3/8". That measurement confirms the cam is positioned correctly. To correct an out-of-spec cam, either add a twist or remove a twist from that cable until the cam sits within the reference range.

Cable Position — Cable must run between the silver reference marks on the cam.
Lobe-to-String Measurement — If no reference marks, measure from cam lobe to string: acceptable range is 5/16" to 3/8".
Correction Method — Add or remove a twist from the cable of the out-of-spec cam to bring it into range.

Note: Adjust only the cable for the cam that is out of spec. Changing the wrong cable will throw off the other cam.

03

APA Cam Lock System

The APA Cam Lock allows the archer to replace cables and string, make adjustments, install accessories, and tune the bow — all without a standard bow press.

Apply pressure to the string or cables to slightly rotate the cam, then insert the stainless steel pin into one of the multiple cam lock holes around the cam perimeter. The pin is stored on the bow when not in use. For bows with Variable Yolk Technology, always adjust from the "Yolk Cable End" rather than the "Single Loop End" to prevent the cable from knotting up.

Cam Lock Pin — Stainless steel pin stored on the bow. Insert into cam lock holes on the cam perimeter to hold cam position.
Activation — Apply light pressure to string or cables to slightly rotate the cam before inserting the pin.
Variable Yolk Technology — Adjust from the Yolk Cable End — not the Single Loop End — to prevent cable knotting.

Important: On bows with Variable Yolk Technology, always adjust from the Yolk Cable End. Adjusting from the Single Loop End will cause the cable to knot up.

Note: No bow press required. The Cam Lock system is one of APA's key advantages — use it for string/cable replacement, accessory installation, and all tuning adjustments.

04

Cam Lean & Variable Yolk Technology

Whether you need to correct cam lean depends entirely on which yolk cable system your APA bow has.

Older APA bows with Served or Static Yolk Cables require cam lean to be corrected before proceeding. However, 2022 models and newer are equipped with Variable Yolk Technology — floating yolk cables that automatically settle exactly where the bow needs them, eliminating cam lean without any manual adjustment. If your bow has Variable Yolk Technology, skip the cam lean correction step entirely and proceed directly to arrow rest setup.

Older APA (Served / Static Yolk) — Cam lean correction is required. Proceed through the cam lean removal steps before moving on.
2022 and Newer (Variable Yolk Technology) — Floating yolk cables self-adjust — cam lean correction is not necessary. Skip to arrow rest setup.

Note: Not sure which system your bow has? Variable Yolk cables float freely and are not served or tied off at a fixed point. If in doubt, bring it in and we'll confirm for you.

05

Top Cam Lean Correction

This step applies to older APA bows with Served or Static Yolk Cables only. Skip this step if your bow has Variable Yolk Technology (2022 and newer).

To correct top cam lean on a right-hand (RH) bow, place a straight edge against the Cam Module. The straight edge should run parallel to the bowstring. If the straight edge is pointing away from the string — meaning the gap is getting wider — the cam is leaning left. To correct this, twist the left side yolk cable (the side the ruler is on), or untwist the other side, depending on how many twists are already present. From the shooter's perspective, this is the Right Side Yolk Cable. For a left-hand (LH) bow, do the opposite.

Check Method — Place a straight edge against the Cam Module. It should run parallel to the bowstring.
Gap Getting Wider — Cam is leaning left. Twist the left side yolk cable (the side the ruler is on), or untwist the opposite side.
RH Bow Reference — The correction cable is the Right Side Yolk Cable from the shooter's perspective.
LH Bow — Do the opposite of the RH correction.

Important: Before twisting or untwisting yolk cables, inspect them first to see how many twists they already have. Do not over-twist, and do not untwist to the point where little or no twists remain.

Note: Make small adjustments — one or two twists at a time — then re-check with the straight edge before continuing.

06

Bottom Cam Lean Correction

This step applies to older APA bows with Served or Static Yolk Cables only. Skip if your bow has Variable Yolk Technology (2022 and newer).

Looking up from the bottom cam, check that there is clearance between the lower cable and the rubber stopper. On a right-hand (RH) bow, if the bottom cable looks like it will touch the rubber stopper when the bow is drawn, put twists on the right-hand bottom yolk cable, or take twists out of the left-hand side — again, from the shooter's perspective. The goal is to have the cable just clear the stopper. For a left-hand (LH) bow, do the opposite. Once the clearance is set, confirm with a straight edge the same way as the top cam. This should remove any remaining cam lean from the bottom cam.

Clearance Check — Look up from the bottom cam and confirm there is clearance between the lower cable and the rubber stopper.
RH Bow — Cable Touching Stopper — Add twists to the right-hand bottom yolk cable, or remove twists from the left-hand side (shooter's perspective).
Target Clearance — Cable should just clear the rubber stopper — not too tight, not too loose.
LH Bow — Do the opposite of the RH correction.
Confirm with Straight Edge — After adjusting, verify with a straight edge against the Cam Module, same as the top cam check.

Important: When looking up from the bottom cam, make sure there is clearance between the lower cable and the rubber stopper. On a RH bow, if the bottom cable looks like it will touch the stopper when drawn, add twists to the right-hand bottom yolk cable or remove twists from the left-hand side. Just make sure the cable clears the stopper. Opposite on LH bow.

Note: After correcting both top and bottom cam lean, re-check axle-to-axle to confirm the bow is still within spec before moving on.

07

Nock Point Alignment Zone & Rest Setup

Once cam lean has been checked and corrected (or confirmed not needed), install and set up the arrow rest.

APA risers feature a machined Nock Point Alignment Zone — a set of reference lines built into the riser that allow you to correctly align the vertical positioning of the arrow's nock point from a side view. Adjust the rest and nock point so the arrow sits parallel to these machined lines. No bow square is required. The APA Twister rest is designed so the launcher cradle is already correctly positioned within the Nock Alignment Zone and is not vertically adjustable. Regardless of rest type, confirm the arrow is level and the nocking point is 90 degrees to the string.

Nock Point Alignment Zone — Machined reference lines on the APA riser. View from the side and align the rest and nock point parallel to these lines.
No Bow Square Required — The machined lines replace the need for a traditional bow square for nock point alignment.
APA Twister Rest — Launcher cradle is pre-positioned for the Nock Alignment Zone. Not vertically adjustable — no height correction needed.
Final Check — Confirm the arrow is level and the nocking point is exactly 90 degrees to the string.

Note: The Nock Alignment Zone is one of APA's built-in tuning advantages — trust the machined lines on the riser rather than relying on a separate bow square.

08

Centre Shot Indicator

Use the APA Centre Shot Indicator to set the horizontal position of the arrow rest. Remove the Cam Lock pin from its storage position and insert it into the precision-drilled hole on the riser above the arrow.

Adjust the arrow rest left or right until the arrow aligns with the laser-etched indicator line. The indicator is directional — it must be oriented correctly on the riser. Look for the painted end or the etched arrow to confirm proper orientation before taking your measurement. Centre shot distance varies by bow generation: older APA dual-cam bows with MX Cam (no RDS) measure approximately 13/16" from the vertical riser face to the centre of the arrow shaft using a tape measure. Bows with static yolks typically measure 5/8" to 11/16" — always check for fletching clearance with the roller guard and buss cable on these models. Newer bows with floating yolk cables (Variable Yolk Technology) have a centre shot of approximately 3/4".

Indicator Orientation — The Centre Shot Indicator is directional. Confirm the painted end or etched arrow is facing the correct direction before adjusting.
Older MX Cam (No RDS) — Centre shot approximately 13/16" from the vertical riser face to the centre of the arrow shaft.
Static Yolk Bows — Centre shot 5/8" to 11/16". Always check for fletching clearance with the roller guard and buss cable.
Floating Yolk / Variable Yolk Technology — Centre shot approximately 3/4" from the vertical riser face.

Note: Always verify fletching clearance after setting centre shot on static yolk bows — the roller guard and buss cable can cause contact issues if the rest is set too far in.

09

Twister Drop Away Rest — Windage Adjustment

This procedure is specific to the APA Twister Drop Away Rest. For all other rests, refer to the manufacturer's instructions.

To adjust windage on the Twister rest, first loosen the black hex screw on the main bracket — this frees the rest to move laterally. Then turn the silver adjustment screw on the side of the rest to dial in your centre shot. You may need to press down on the spring to access the screw head. Once centre shot is achieved, retighten the main bracket screw to lock the position.

Black Hex Screw (Main Bracket) — Loosen to allow lateral windage movement. Retighten when centre shot is set.
Silver Adjustment Screw — Turn to move the rest left or right until centre shot is achieved. Press down on the spring if needed to reach the screw head.
Spring Access — Press down on the spring to expose the silver adjustment screw head if it is not immediately accessible.

Important: Do NOT touch the Red Screw — it is a factory-set calibration screw. Adjusting it will throw off the rest's timing and require a full reset. Remember to retighten the main bracket black hex screw when finished.

Note: Make small turns on the silver adjustment screw and re-check centre shot alignment after each adjustment before locking down the bracket.

10

Torque-Free Limb Anchor & Rest Cord Timing

The APA Torque-Free Limb Anchor provides a secure, dedicated tie-in point for a limb-driven drop away rest, eliminating side-to-side torque on the limb forks for improved accuracy.

When installing the Twister 360 rest cord, position the supplied spring approximately 2 inches below the limb. The rest cord timing is correct when the tension just stretches the spring enough to create a slight gap between the coils — not compressed, not slack. As the cord stretches during the draw cycle, the spring compresses slightly, keeping the rest in time. Do not overtighten the screw at the rest body, as this causes premature wear on the cord. The coil spring is there specifically to reduce stress on the cord and extend its life.

Spring Position — Position the supplied coil spring approximately 2 inches below the limb when installing the Twister 360 rest cord.
Correct Cord Tension — Tension should just stretch the spring enough to create a slight gap between coils — not fully compressed, not loose.
How It Works — As the cord stretches during the draw cycle, the spring compresses to absorb the load and keep the rest in time.
Rest Body Screw — Do not overtighten. The coil spring reduces cord stress — let it do its job.

Important: Do not overtighten the screw at the rest body. Overtightening causes premature wear on the rest cord.

Note: If you notice fletching wear or marks on the rest, check the rest cord first — it likely needs re-adjustment. It is unlikely the bow has gone out of tune.

11

Choosing the Right Arrow Rest for APA Bows

APA risers are narrow front to back. This affects which arrow rests will work correctly — not all rests are compatible without ongoing problems.

Many rests have a longer attachment arm. When the launcher is positioned correctly — close to the back of the riser shelf — the rest bracket extends in front of the riser, making it impossible to use the small set screw that bites down on the riser to keep the rest level and secure. With limb-driven or cable-driven rests, the repetitive tension on the rest cord will gradually tug the back of the rest out of level over time, requiring continuous readjustment. When rests are mounted per the manufacturer's instructions, the launcher ends up sitting too far back from the riser, which creates two problems: first, any slight bow hand torque is magnified because the holding hand is ahead of the launcher, hurting accuracy and arrow grouping; second, on bows with a shorter brace height like the King Cobra DGX, the arrow fletching can get caught in the vertical arrow launcher. APA-designed rests are built around the riser geometry and avoid these issues entirely. If using a third-party rest, look for one with a short mounting arm bracket — no longer than 1-1/2".

Root Cause — APA risers are narrow front to back. Long-arm rests cannot use the set screw to lock level when the launcher is in the correct position.
Limb / Cable Driven Rests — Repetitive cord tension gradually pulls the rest out of level over time. Requires continuous readjustment.
Problem 1 — Accuracy — Launcher too far back puts the bow hand ahead of it. Any bow hand torque is magnified, hurting groupings.
Problem 2 — Fletching Clearance — On shorter brace height bows like the King Cobra DGX, fletching can catch in the vertical arrow launcher.
Recommended Solution — Use an APA-designed rest, or choose a third-party rest with a short mounting arm bracket no longer than 1-1/2".

Note: When in doubt, use an APA-designed rest. They are built specifically for APA riser geometry and eliminate all of these fitment issues.

12

Pre-Timing Checklist

Before checking and adjusting cam timing, confirm that all of the following steps have been completed in order. Cam timing cannot be accurately set if any of these are out of spec.

Work through this checklist before proceeding to cam timing. Each item must be correct before moving on — timing adjustments made on a bow with incorrect specs, cam positioning, or cam lean will not hold and will need to be redone.

Step 1 — Specs — Bow is at maximum poundage. Axle-to-axle and brace height have been checked and are within spec.
Step 2 — Cam Positioning at Rest — Cable position relative to each cam has been checked and corrected. Cams sit within the silver reference marks or within the 5/16"–3/8" measurement range.
Steps 3–6 — Cam Lean — Cam lean on both top and bottom cams has been checked and corrected (or confirmed not required for Variable Yolk Technology bows).
Steps 7–11 — Arrow Rest — Arrow rest has been installed and adjusted per APA requirements: correct rest type, nock point aligned, centre shot set, windage dialled in.

Note: If anything on this checklist is not yet complete, go back and finish it before touching cam timing. Getting the order right saves a lot of re-work.

13

Cam Timing — Draw Board Warning

Before checking cam timing, there is one critical rule that applies to every APA dual-cam bow: a draw board cannot be used.

APA dual-cam bows have two cams that are the same size and are mirror images of each other. The grip is not centred between the two cams — the bottom cam sits closer to the centre of the grip than the top cam. When a draw board is used, this offset means the cams are not loaded equally, so timing cannot be accurately set. You must draw the bow back by hand using a release aid with an arrow nocked, or use a safe drawing device. Before drawing, set the draw length to the shooter and reduce the draw weight by 4 full turns — this makes the bow easier to draw and ensures the draw board will not give a false reading. Binary and hybrid cam systems are different because they use two cams of different diameters, which allows a draw board to be used. APA dual-cam bows do not share this characteristic.

Why No Draw Board — APA dual cams are the same size and mirror images. The grip is not centred — the bottom cam is closer to the grip centre than the top. A draw board loads the cams unequally, giving a false timing reading.
Correct Drawing Method — Draw the bow back by hand using a release aid with an arrow nocked, or use a safe drawing device.
Reduce Draw Weight First — Back the draw weight off 4 full turns before checking timing. This makes the bow easier to draw and prevents the draw board from giving a false indication.
Set Draw Length First — Set the draw length to the shooter before drawing back to check timing.
Binary / Hybrid Cams — Binary and hybrid cam systems use two different diameter cams, which allows a draw board to be used. This does not apply to APA dual-cam bows.

Important: A draw board cannot be used to check or correct cam timing on an APA dual-cam bow. The cams are the same size and the grip is not centred — a draw board will give a false reading. Always draw by hand with a release and nocked arrow, or use a safe drawing device. Reduce draw weight 4 full turns before proceeding.

Note: Reducing draw weight 4 full turns before checking timing is not optional — it is part of the process. Restore draw weight to the correct setting after timing is confirmed.

14

Micro Tune Cable Guide & Timing Correction

With the bow drawn back using a release and nocked arrow (or safe drawing device), check whether both cams drop into the draw valley at the same time. If it is difficult to see the cable relative to the draw module groove, you should be able to feel whether the cams are out of time.

At full draw, the top cam should show the cable lying flat in the module groove. The bottom cam should match — if there is a gap between the module groove and the buss cable on the bottom cam, the cams are out of time. To correct this, the buss cable that attaches to the top cam is shorter than the bottom cable because it has more twists. Remove twists from this cable, or add twists to the opposite buss cable, until both cams drop into the valley simultaneously. Before making any timing corrections, the APA patented Micro Tune Cable Guide must be set to its neutral position — pre-set so that equal adjustment is available in both directions. Do not attempt to correct timing with the Micro Tune off-centre. When twisting or untwisting cables, inspect them first to see how many twists they already have. Do not over-twist, and do not remove twists from a cable that is not twisted equally to the other. Most cables are served, and half a twist or so may be all that is needed. On bows without RDS that have Static Yolk Cables, it may sometimes be necessary to twist the yolk cables to fine-tune cam timing — if so, twist each side equally.

Micro Tune — Neutral Position First — The Micro Tune Cable Guide must be set to its neutral (centre) position before checking or correcting timing. It must be pre-set so equal adjustment is available in both directions.
How to Check Timing — Draw the bow back with a release and nocked arrow. Both cams should drop into the draw valley at the same time. The top cam cable should lie flat in the module groove at full draw.
Bottom Cam Out of Time — A gap between the module groove and the buss cable on the bottom cam at full draw means the cams are out of time.
Correction — Remove or Add Twists — The buss cable attaching to the top cam has more twists (is shorter). Remove twists from this cable, or add twists to the opposite buss cable, until both cams are in time.
Twist Caution — Inspect cables before adjusting — check how many twists each already has. Do not over-twist. Do not remove twists from a cable that is not equally twisted to the other. Half a twist may be all that is needed.
Static Yolk Bows (No RDS) — On bows without RDS with Static Yolk Cables, yolk cables may need to be twisted to fine-tune timing. Twist each side equally.

Important: The Micro Tune Cable Guide must be checked and set to its neutral position before proceeding with cam timing. Do not attempt timing corrections with the Micro Tune off-centre. When twisting or untwisting cables, inspect them first. Do not over-twist, and do not remove twists from a cable that is not equally twisted to the other — half a twist or so may be all that is needed.

Note: If it is hard to see the cable in the module groove at full draw, trust what you feel — both cams should reach the valley at the same moment. Any hesitation or stagger between them is a sign the timing needs correction.

15

Variable Yolk Timing Adjustment

On bows equipped with Variable Yolk Technology, cable adjustments for cam timing must always be made from the yolk end — not the single loop end.

The cables on Variable Yolk bows are mostly served. Twisting from the single loop end will only add or remove poundage from the bow — it will make little to no change in cam timing. To actually affect cam timing, you must adjust the buss cable from the yolk end. This is the only effective point of adjustment on these bows for timing correction.

Correct Adjustment Point — Always twist or untwist the buss cable from the yolk end when correcting cam timing on Variable Yolk bows.
Single Loop End — Do Not Use for Timing — Twisting from the single loop end only changes bow poundage. It will have little to no effect on cam timing.
Why This Matters — Cables on Variable Yolk bows are mostly served. The yolk end is the only point where twisting produces a meaningful timing correction.

Important: Bows with Variable Yolk Technology must have their cables twisted or untwisted from the yolk end when timing the bow. Adjusting the buss cable from the yolk end is required — adjusting from the single loop end will only affect poundage, not timing.

Note: If your timing adjustments do not seem to be making a difference, check which end of the cable you are twisting. On Variable Yolk bows, the yolk end is the only end that moves the timing.

16

RDS Timing — Hatch Marks

On bows equipped with the RDS (Roller Drive System), setting cam timing is simpler than on non-RDS bows. The RDS hatch marks give you a repeatable reference point for matching both cams.

With the RDS backed all the way off, draw the bowstring to full draw using a draw board until one of the buss cables is lying flat in the module groove. It is preferable to set the top cam first. While the bow is still drawn, adjust the RDS so the limb stop just touches the underside of the limb. Tighten the RDS screw and take the bow out of the draw board. Next, count the number of hatch marks (tic marks) machined into the RDS, starting from the long end backwards to the centre of the RDS locking screw. Then adjust the other (bottom) RDS to the same reference mark as the first one. Providing all other settings are correct and the limbs are turned out equally, timing should be very close. Fine-tune cam timing using cable twists or the Micro Tune. You can also adjust the RDS of each cam one tic mark shorter or longer depending on which feels better at full draw.

Starting Position — Back the RDS all the way off before beginning. Draw the bow to full draw using a draw board.
Set Top Cam First — Draw until one buss cable is lying flat in the module groove. Preferred to start with the top cam.
Set the Limb Stop — While the bow is still drawn, adjust the RDS so the limb stop just touches the underside of the limb. Tighten the RDS screw, then remove the bow from the draw board.
Count the Hatch Marks — Count the tic marks machined into the RDS from the long end backwards to the centre of the RDS locking screw. Note the reference mark number.
Match the Bottom RDS — Adjust the bottom RDS to the same reference mark as the top. With all other settings correct and limbs turned out equally, timing should be very close.
Fine Tuning — Fine-tune with cable twists or the Micro Tune. Adjust each RDS one tic mark shorter or longer depending on which feels better at full draw.

Note: The RDS hatch marks make it easy to return to a known timing reference if you ever need to re-tune or replace cables. Write down your reference mark numbers once the bow is dialled in.

17

RDS Timing — 2024 Update (Letters A–S)

New for 2024: current model APA bows feature an updated RDS with letters marked A through S instead of hatch marks. This makes matching cam positions and setting draw length significantly easier.

Each new bow ships with a sticker on the bottom limb showing the draw module and its corresponding RDS letter setting. To set the RDS, position it so the letter is centred with the centre of the RDS screw head. This is a solid starting point — from there, fine adjustments of one letter position in either direction can be made to suit personal feel and preference at full draw.

Letter Scale (A–S) — Replaces the older hatch mark system on 2024 and newer current model bows. Letters run A through S for precise, easy-to-read positioning.
Bottom Limb Sticker — Each new bow includes a sticker on the bottom limb showing the draw module and its corresponding RDS letter setting.
Setting the RDS — Position the RDS so the correct letter is centred with the centre of the RDS screw head.
Fine Tuning — The letter position from the sticker is a starting point. Adjust one letter shorter or longer to suit personal feel and preference at full draw.

Note: Keep the bottom limb sticker intact — it is your reference for the factory-recommended starting position. If the sticker is ever lost, bring the bow in and we can help you find the right starting letter.

18

Paper Tuning — Prerequisites & Nock Left/Right

Before paper tuning, confirm that all previous steps are complete and that you are shooting correctly. A paper tear caused by poor form or incorrect equipment cannot be fixed by tuning.

When you shoot through paper and get a left or right tear of 1 inch or more — or a tear that does not improve with adjustments — the likely causes are: torquing the bow when shooting, fletching contact with the arrow rest or buss cables, or incorrect arrow spine. Make sure you are shooting correctly spined arrows, that there is no fletching contact, and that you are shooting with a relaxed bow hand. Do not punch the trigger. Correct these flaws before beginning to tune. A nock left tear means the arrow is fishtailing and the fletching is tearing to the left of the point. To correct on a right-hand bow, move the arrow rest to the right — a very small adjustment of approximately 1/16" should eliminate the tear. On bows with static yolk cables, you could also add a twist or so to the upper left-hand side yolk cable. However, it is better to move the rest slightly than to yolk tune, since yolk adjustments may put the cams out of time again. Bows with Variable Yolk Technology cannot be yolk tuned. In practice, paper tears on these bows should be minimal to non-existent, especially on bows that also have the Centre Shot Indicator feature. For a nock right tear, do the opposite of the nock left correction.

Prerequisites — Check These First — Correct arrow spine, no fletching contact with rest or buss cables, relaxed bow hand, no trigger punching. Fix these before paper tuning.
When to Suspect Form or Equipment — A tear of 1 inch or more, or a tear that does not improve with rest adjustments, usually points to torque, fletching contact, or wrong spine — not a tuning issue.
Nock Left Tear (RH Bow) — Move the arrow rest to the right. Approximately 1/16" is usually enough to eliminate the tear.
Yolk Tune Option (Static Yolk Only) — On static yolk bows, adding a twist to the upper left-hand side yolk cable can also correct a nock left tear. However, moving the rest is preferred — yolk adjustments risk putting the cams out of time.
Variable Yolk Bows — Cannot be yolk tuned. Paper tears should be minimal to non-existent on these bows, especially with the Centre Shot Indicator.
Nock Right Tear — Do the opposite of the nock left correction — move the rest to the left.

Note: If your paper tears are large or inconsistent shot to shot, stop and check form before adjusting the rest. Tuning a bow that is being torqued will not produce consistent results.

19

Paper Tuning — Nock Low/High & Final Broadhead Tune

A nock low tear means the arrow is porpoising out of the bow — the point enters the paper and the fletching tears below the point. A nock high tear is the opposite. Both are vertical tears and are addressed differently from left/right tears.

A nock low tear is typically caused by the bottom cam running slightly fast, or by an arrow spine that is too weak for the bow. To correct it: confirm you are shooting the proper spine arrow, loosen tension on the Micro Tune, remove a twist from the bottom buss cable, or add a twist to the top buss cable. For a nock high tear, do the exact opposite. Vertical tears should be fairly minimal on bows where the RDS on each cam has been pre-set equally. If you have a nock high or low tear that will not correct itself, you must check the nocking point and confirm the arrow is level. Do not raise or lower the rest — adjust the nocking point by moving it the correct direction along the centre serving. Once all adjustments are made, the bow is tuned and should produce a perfect paper tear. As a final reminder: make sure there is no fletching contact, shoot with a relaxed bow hand, and do not punch the trigger. Correct any form flaws before tuning. Regarding fixed-blade broadheads: experience has proven many times over that no further tuning is required after completing this process. Broadheads shot at 20, 30, and 40 yards have consistently grouped with field points. The closer your broadheads are to your field points is a reflection of your shooting ability — not a tuning problem.

Nock Low Tear — Causes — Bottom cam running slightly fast, or arrow spine too weak for the bow.
Nock Low Tear — Corrections — Confirm correct arrow spine. Loosen Micro Tune tension. Remove a twist from the bottom buss cable, or add a twist to the top buss cable.
Nock High Tear — Do the exact opposite of the nock low corrections.
RDS Bows — Vertical tears should be minimal when the RDS on each cam has been pre-set equally.
Persistent Vertical Tear — Do not raise or lower the rest. Check the nocking point and confirm the arrow is level. Adjust the nocking point by moving it the correct direction along the centre serving.
Fixed-Blade Broadheads — No further tuning required after completing this process. Broadheads will group with field points at 20, 30, and 40 yards. Grouping consistency reflects shooting ability, not a tuning issue.

Important: Do not raise or lower the rest to correct a vertical paper tear. The rest height was set in Step 7 using the Nock Point Alignment Zone. Adjust the nocking point along the centre serving instead.

Note: Once you have a perfect paper tear with field points, go straight to the range with broadheads — no additional tuning step is needed. If broadheads are grouping differently than field points, the answer is more practice, not more tuning.

20

APA Shift Tune Technology — Correcting Persistent Left/Right Tears

If you have completed all previous tuning steps and still have a persistent left or right paper tear, APA Shift Tune Technology provides a tool-free solution. This innovation allows you to effortlessly adjust the tune of your APA bow by shifting the cable yokes left or right — no Allen wrench required.

APA Shift Tune Technology works by shifting the cable yokes laterally to influence arrow flight. If your arrow tail is tearing left, shift the yokes left. If your arrow tail is tearing right, shift the yokes right. The adjustment is simple and tool-free — no Allen wrench is needed. Shift Tune comes standard on certain APA bow models and can be added to any APA Dual Cam bow. Make small incremental shifts and re-paper tune after each adjustment until you achieve a perfect bullet hole. This is a fine-tuning step — only use it after confirming correct arrow spine, no fletching contact, proper rest position, and good shooting form.

Tail Left — Shift Left — If the arrow tail is tearing to the left through paper, shift the cable yokes to the left. Make a small adjustment, then re-paper tune to check the result.
Tail Right — Shift Right — If the arrow tail is tearing to the right through paper, shift the cable yokes to the right. Make a small adjustment, then re-paper tune to check the result.
No Tools Required — Shift Tune adjustments are completely tool-free — no Allen wrench or other tools needed. Adjustments are made by hand directly on the cable yoke assembly.
Compatibility — Comes standard on certain APA bow models. Can be added to any APA Dual Cam bow as an aftermarket upgrade.
When to Use Shift Tune — Only use Shift Tune after completing all previous steps and confirming correct arrow spine, no fletching contact, proper rest position, and sound shooting form. This is a final fine-tuning tool, not a first step.

Note: Make small, incremental shifts and re-paper tune after each adjustment. Over-shifting can introduce new problems. One small shift at a time is all it takes.

Final Validation

Your bow is tuned when every checkpoint below is confirmed.

Correct arrow spine confirmed

Shooting properly spined arrows for your bow weight and draw length.

Fletching clearance verified

No contact between fletching and arrow rest, roller guard, or buss cables.

Nocking point set and level

Arrow is level; nocking point is 90° to the string and positioned in the Nock Alignment Zone.

Cam timing locked in

Both cams drop into the draw valley simultaneously. RDS pre-set equally on each cam.

Perfect paper tear achieved

Clean bullet hole through paper with field points at 6–8 feet.

Broadhead grouping tested

Fixed-blade broadheads grouping with field points at 20, 30, and 40 yards.

You're done. No further tuning is required. If broadheads are grouping differently than field points, the answer is more practice — not more tuning. Shoot with a relaxed bow hand, do not punch the trigger, and enjoy a properly tuned APA bow.

Need a Hand Getting Dialled In?

Bring your APA bow into The Archery Guy in Thunder Bay. We set up and tune every APA bow we sell and are happy to work through any tuning issue with you.

The Archery Guy

Your local archery pro shop — serving beginners, hunters, and competitive archers across Canada.

Services

  • Bow Tuning & Setup
  • Custom Fitting
  • Bow Repairs
  • Arrow Building

Visit Us

thearcheryguy.ca

Canada

© 2026 The Archery Guy. All rights reserved.